Exactly How to Set up a Tub Yourself
Exactly How to Set up a Tub Yourself
Blog Article
Listed here down the page you will find additional incredibly good facts in regards to Installing A Bathtub.
Mounting a tub isn't exactly brain surgery, however it does require strong plumbing, carpentry, and also in some cases, tiling abilities. Replacing an old bathtub with a brand-new one is also a reasonably challenging task. If the old tub is readily obtainable, the project can relocate rapidly; if you need to open up a wall to get rid of the old tub and also position the brand-new tub, the job is much harder. In either instance, the task is within a house handyman's skills, although you will certainly need a helper to vacate the old tub as well as set in the brand-new one. Make sure you have certified yourself for the work and fit attempting it. As opposed to hiring a specialist to take control of a halfway-completed job, it is far better to consider utilizing one prior to you start. Chances are you might need an expert plumber to make tube links.
This post will assist you mount a new tub in your washroom if you have currently bought a new bathtub and don't require to transform the arrangement of your previous water system pipelines.
Your devices and material checklist must comprise the following:
Getting ready for the Installment
Firstly, the supporting structure provided with the bath ought to be fitted (if needed) according to the supplier's instructions. Next, fit the taps or mixer to the tub. When suitable the faucet block, it is necessary to see to it that if the faucet features a plastic washing machine, it is fitted between the bath as well as the taps. On a plastic bathroom, it is additionally reasonable to fit a supporting plate under the taps unit to avoid stress on the tub.
Fit the adaptable faucet adapters to the bottom of both taps using 2 nuts and olives (in some cases supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the outlet through the hole in the bath. Use the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Ensure you use every one of the provided washing machines.
Attach the catch to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bath ought to now be ready to be fitted in its last placement.
Removing Old Touches
If you require to replace old taps with new ones as a part of your installment, after that the first thing you ought to do is disconnect the water supply. After doing so, turn on the faucets to drain any water remaining in the system. The procedure of removing the existing taps can be fairly bothersome as a result of the restricted gain access to that is often the instance.
Make use of a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipes to the faucets. Have a fabric prepared for the remaining water that will certainly originate from the pipes. Once the supply pipes have been gotten rid of, make use of the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the single faucets from transforming during this procedure. When the taps have actually been eliminated, the holes in the bath/basin will certainly have to be cleaned of any kind of old securing compound.
Prior to carrying on to fit the new taps, contrast the pipeline connections on the old faucets to the new faucets. If the old faucets are longer than the new faucets, then a shank adapter is needed for the brand-new taps to fit.
Mounting the Tub
Making use of both wooden boards under its feet, position the bath tub in the needed position. The wood boards are useful in equally spreading the weight of the bath tub over the location of the boards rather than focusing all the weight onto 4 small factors.
The next objective is to guarantee that the bath tub is leveled all round. This can be accomplished by examining the spirit level and also adjusting the feet on the bath tub until the level reads degree.
To install taps, fit all-time low of the furthest versatile tap port to the appropriate supply pipe by making a compression sign up with; after that do the exact same for the various other tap.
Turn on the water supply as well as examine all joints as well as brand-new pipework for leaks as well as tighten them if essential. Fill the bath tub and likewise examine the overflow outlet as well as the typical electrical outlet for leaks.
Lastly, fix the bath paneling as defined in the manufacturer's user's manual. Tiling as well as securing around the bathtub ought to wait till the bathtub has been made use of at least once as this will certainly resolve it into its final setting.
Suitable New Taps
If the tails of the new faucets are plastic, after that you will require a plastic connector to avoid damages to the string. One end of the connector fits on the plastic tail of the tap as well as the various other end supplies a link to the existent supply pipes.
If you need to fit a monobloc, after that you will certainly require decreasing couplers, which links the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next, position the faucet in the placing opening in the bath/basin making certain that the washers remain in area between the tap as well as the sink. Protect the faucet in position with the supplier offered backnut. When the faucet is firmly in position, the supply pipelines can be connected to the tails of the taps. The taps can either be connected by using corrugated copper piping or with typical tap ports. The previous kind must be attached to the faucet finishes initially, tightening only by hand. The supply pipes can later on be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Bathtub
In the area where the bath meets the tile, it is required to seal the joins with a silicone rubber caulking. This is essential as the fitting can move enough to crack a rigid seal, causing the water to penetrate the wall in between the bathroom as well as the tiling, causing issues with moisture as well as possible leaks to the ceiling below.
You can choose from a selection of coloured sealers to blend in your components and also installations. They are offered in tubes as well as cartridges, and are capable of securing voids approximately a size of 3mm (1/8 inch). If you have a larger gap to fill, you can load it with spins of soaked paper or soft rope. Bear in mind to constantly fill up the bathtub with water before securing, to enable the motion experienced when the tub remains in usage. The sealant can fracture rather early if you do not consider this movement prior to sealing.
Alternatively, ceramic coving or quadrant floor tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also easily available on the marketplace. It is a good idea to fit the ceramic tiles using waterproof or water resistant adhesive and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As an enthusiastic reader on How to Install a Bathtub Yourself, I think sharing that blog post was really helpful. Loved our blog? Please share it. Help another person find it. We value reading our article about Installing A Bathtub.
Check Us Out
Report this page